Mike how is you hammer gap solve?
Beiträge von BalkanCowboy
-
-
Isno are you a frustrated troll, or an unsatisfied troll?:-) We're talking here about how we can turn 3J into 5. I don't know if you know that we have a rubber bullet gun paradise in Hungary, and I can go in any time and buy a Baikal shotgun converted to a rubber bullet that fires an 18mm bullet with 140J energy. I guess there's not much point talking about unnecessary tuning from here:-)
-
Flupp in that case..its not from the gun. Thanx god:-)
It's very difficult to have this technical discussion with a translator:-) I checked today what is the maximum hammer tightening that does not press the valve feed button yet. I also tightened it on the part that is above the dispenser. However, this spring loaded fake fire pin wouldn't let me get any closer since the very movement that gives a "shock absorption" wouldn't let me get the hammer fixed any closer no matter how I filed it. So I reduced the length of the spring behind the fire pin. I will make a video of the result.
-
-
Ich habe den Hammer an der üblichen Stelle rasiert und auch unterhalb der Stelle, wo das Ventil auf den Druckknopf trifft. Dann habe ich herausgefunden, dass die falsche Stiftfeder im Hammer ihn zurückdrückt. Ich habe sie herausgenommen, die Feder abgeschnitten und sie wieder zusammengesetzt. Test, Schnappschuss, und er hinterließ eine Markierung an der Stelle, an der er einschlug. Ein neu ausgewähltes restliches Federstück und eine Papierunterlegscheibe scheinen das Problem vorerst gelöst zu haben:-)
-
Azt hiszem vennem kell egy úgy kalapács fake pin készletet:-))))
-
Super. I have been doing the hammer position job for 30min. I hope it will be more correct. Or i finally make a display gun:-)))
-
So the gas flows around it, and the thinner diameter lets more gas through? And where can we found this part in the Colt SAA?
-
Did you rasp off the outside of that part of the pipe? This affects the size of the inner tube. Sorry if I don't understand it that way.
-
Falco, I remember this valve expansion on youtube has been tried on many different airguns with very little success. Do you have any other pictures of where and how to modify the gun?
-
I have two 7,5 inch pellet colt saa 4.5mm. They are very strong. The older weathered version (NRA) somehow more accurate than the gold-nickel but it doesnt matter now. Both shot through a medium thickness tin can from front to back.
-
-
I can't get it out of my head that we should somehow increase the power of the RAM weapon.I don't know if it's limited by the valve system itself or if the CO2 capsule can't handle more pressure than this (supposedly) 4-5J. We know all models have the same valve but the crony says the 7.5" is much stronger and I'm not sure if it's just the extra 5 cm of barrel length. The Dan Wesson models have a different valve system, the 8 inch has the strongest, they tune the smaller barreled models to put that in.
-
Oh you lucky 7,5 inch RAM version.:-) The non-circular bolt may tighten the spring a little more, or it may be larger than 2mm which is half the gap, so it should be a good tight fit. Which I like by the way. I plan to use some file and common sense to let the hammer in even closer, question is whether the fake fire pin spring movement is needed in the cock if the gas valve would not be pushed by the cock in its original position.
-
Mike egy kicsit szabálytalan az a szög vagy mi, lehet nem a legjobb forma. De az biztos piszok feszes lesz a rugó.
-
Én nem fúrtam át a kalapácsot. Egy picit mélyedést fúrtam bele, és egy 2mm átmérőjű szögből vágtam le egy kb 4mm-es darabot, amit bele illesztettem(nem tudom pontosan milyen hosszú kellett), és a sarokba még szuper ragasztóval is rögzítettem. Pompásan működik. Nekem az eredeti rugóval is nagyszerű érzet, ha bármi gond lenne, mivel az eredeti colt alkatrészek érvényesek rá, filléres a csere.
-
-
Nagyon ügyes! Szép a kakas helyzete! De én a 2mm-es rés csökkentésért azt hiszem nem bolygatom tovább. Ha tudnék venni egy használt/sérült darabot akkor azon talán. A sima metódussal csökkentett rés erősebb kakas felhúzás érzetet ad, visszaugráskor a helyére nem mozog. Tudtam volna az eredeti módszerrel még közelebb engedni 1mm-t de szeretném ha a cink ötvözetet a kakasban lévő csillapító ütné.
-
Mike i do at least 60-70 shot with a single 12gr capsule.
-
I think you can cut the barrel, but around the barrel mouth you have to polish or crome plating.